The FNX-IV series integrates Industry 4.0 IoT capabilities, a new high-plasticization screw, ISO20430 safety compliance, and an updated clamp mechanism making the FNX series even more versatile.
The Nissei FNX-IV Series hybrid injection molding machines combine hydraulic durability and cost savings with electric efficiency and repeatability. The FNX-IV serries is produced with clamping forces from 81 to 455 tons. Equipped with Nissei’s innovative X-Pump® system and an IoT-enabled TACT5 controller. These machines deliver precise, energy-efficient performance suitable for a wide range of applications, from precision thin-wall to thick-wall molding.
Key features of the FNX-IV Series include a high-rigidity straight-hydraulic clamping unit (toggle free), quick injection response, and stable control at ultra-low velocities. The X-Pump® system intelligently combines hydraulic control with the precision of a servo drive, achieving significant energy savings by operating the servomotor only as needed. The TACT®V controller has an intuitive interface, IoT & Industry 4.0 connectivity, and simplifies equipment setup, monitoring, and maintenance routines.
Choosing the FNX-IV Series provides manufacturers with a smart, connected hybrid solution that balances performance with electric-level efficiency. X-Pump machines are time tested, quiet, and have exceptional injection repeatability as well as low velocity/pressure controllability. The new IoT-enabled TACT5 controller simplifies operation and offers connectivity with auxiliary equipment and automation, remote monitoring, and provides connectivity for remote troubleshooting.
| Item | Unit | 9A (std) | | | 12A | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Screw diameter | inch (mm) | AA 1.02 (26) | A 1.10 (28) | B 1.26 (32) | C 1.42 (36) | | | AA 1.10 (28) | A 1.26 (32) | B 1.42 (36) | C 1.57 (40) |
| Injection capacity | inch3 (cm3) (oz) | 3.6 (59) (2.0) | 4.2 (69) (2.3) | 5.5 (90) (3.0) | 7.0 (114) (3.8) | | | 4.7 (77) (2.6) | 6.2 (101) (3.4) | 7.7 (127) (4.3) | 9.6 (157) (5.3) |
| Max. injection pressure | psi (MPa) (kgf/cm2) | 38470 (265) (2705) | 35410 (244) (2490) | 27160 (187) (1910) | 21330 (147) (1500) | | | 38470 (265) (2705) | 32850 (226) (2310) | 26020 (179) (1830) | 21050 (145) (1480) |
| Clamping force | USton (kN) (tf) | 89 (792) (81) | ||||||||
| Clamping stroke | inch (mm) | 18.5 (470) | ||||||||
| Min. mold thickness | inch (mm) | 7.9 (200) | ||||||||
| Max. daylight opening | inch (mm) | 26.4 (670) | ||||||||
| Tie bar clearance (H×V) | inch (mm) | 16.5×16.5 (420×420) | ||||||||
| Die plate dimensions (H×V) | inch (mm) | 22.8×22.8 (580×580) | ||||||||
| Ejector stroke | inch (mm) | 3.0 (75) | ||||||||
| Item | Unit | 12A (std) | | | 18A | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Screw diameter | inch (mm) | AA 1.10 (28) | A 1.26 (32) | B 1.42 (36) | C 1.57 (40) | | | AA 1.26 (32) | A 1.42 (36) | B 1.57 (40) | C 1.77 (45) |
| Injection capacity | inch3 (cm3) (oz) | 4.7 (77) (2.6) | 6.2 (101) (3.4) | 7.7 (127) (4.3) | 9.6 (157) (5.3) | | | 7.1 (117) (3.9) | 9.0 (147) (4.9) | 11.1 (182) (6.1) | 14.1 (231) (7.7) |
| Max. injection pressure | psi (MPa) (kgf/cm2) | 38470 (265) (2700) | 32850 (226) (2310) | 26020 (179) (1830) | 21050 (145) (1480) | | | 38470 (265) (2705) | 32280 (222) (2270) | 26170 (180) (1840) | 20620 (142) (1450) |
| Clamping force | USton (kN) (tf) | 123 (1100) (112) | ||||||||
| Clamping stroke | inch (mm) | 20.5 (520) | ||||||||
| Min. mold thickness | inch (mm) | 7.9 (200) | ||||||||
| Max. daylight opening | inch (mm) | 28.3 (720) | ||||||||
| Tie bar clearance (H×V) | inch (mm) | 18.1×18.1 (460×460) | ||||||||
| Die plate dimensions (H×V) | inch (mm) | 25.5×25.5 (647×647) | ||||||||
| Ejector stroke | inch (mm) | 3.3 (85) | ||||||||
| Item | Unit | 25A (std) | | | 36A | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Screw diameter | inch (mm) | AA 1.42 (36) | A 1.57 (40) | B 1.77 (45) | C 1.97 (50) | | | A 1.77 (45) | B 1.97 (50) | C 2.20 (56) | |
| Injection capacity | inch3 (cm3) (oz) | 9.9 (163) (5.5) | 12.3 (201) (6.7) | 15.5 (254) (8.5) | 19.2 (314) (10.5) | | | 17.5 (286) (9.6) | 21.5 (353) (11.8) | 27.0 (443) (14.8) | |
| Max. injection pressure | psi (MPa) (kgf/cm2) | 36970 (255) (2600) | 31780 (219) (2235) | 25170 (173) (1770) | 20340 (140) (1430) | | | 30010 (207) (2110) | 24390 (168) (1715) | 19480 (134) (1370) | |
| Clamping force | USton (kN) (tf) | 154 (1370) (140) | ||||||||
| Clamping stroke | inch (mm) | 23.6 (600) | ||||||||
| Min. mold thickness | inch (mm) | 9.8 (250) | ||||||||
| Max. daylight opening | inch (mm) | 33.5 (850) | ||||||||
| Tie bar clearance (H×V) | inch (mm) | 20.1×20.1 (510×510) | ||||||||
| Die plate dimensions (H×V) | inch (mm) | 28.7×28.7 (730×730) | ||||||||
| Ejector stroke | inch (mm) | 3.5 (90) | ||||||||
| Item | Unit | 25A | | | 36A (std) | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Screw diameter | inch (mm) | AA 1.42 (36) | A 1.57 (40) | B 1.77 (45) | C 1.97 (50) | | | A 1.77 (45) | B 1.97 (50) | C 2.20 (56) | |
| Injection capacity | inch3 (cm3) (oz) | 9.9 (163) (5.5) | 12.3 (201) (6.7) | 15.5 (254) (8.5) | 19.2 (314) (10.5) | | | 17.5 (286) (9.6) | 21.5 (353) (11.8) | 27.0 (443) (14.8) | |
| Max. injection pressure | psi (MPa) (kgf/cm2) | 36970 (255) (2600) | 31780 (219) (2235) | 25170 (173) (1770) | 20340 (140) (1430) | | | 30010 (207) (2110) | 24390 (168) (1715) | 19480 (134) (1370) | |
| Clamping force | USton (kN) (tf) | 197 (1750) (179) | ||||||||
| Clamping stroke | inch (mm) | 27.6 (700) | ||||||||
| Min. mold thickness | inch (mm) | 9.8 (250) | ||||||||
| Max. daylight opening | inch (mm) | 37.4 (950) | ||||||||
| Tie bar clearance (H×V) | inch (mm) | 22.0×22.0 (560×560) | ||||||||
| Die plate dimensions (H×V) | inch (mm) | 31.5×31.5 (800×800) | ||||||||
| Ejector stroke | inch (mm) | 4.3 | ||||||||
| Item | Unit | 50A (std) | | | 71A | ||||
|---|---|---|---|---|---|---|---|---|
| Screw diameter | inch (mm) | A 1.97 (50) | B 2.20 (56) | C 2.48 (63) | | | A 2.20 (56) | B 2.48 (63) | C 2.80 (71) |
| Injection capacity | inch3 (cm3) (oz) | 24.5 (402) (13.5) | 30.8 (505) (16.9) | 39.0 (639) (21.4) | | | 33.8 (554) (18.6) | 42.8 (701) (23.5) | 54.4 (891) (29.9) |
| Max. injection pressure | psi (MPa) (kgf/cm2) | 28730 (198) (2020) | 22900 (158) (1610) | 18200 (125) (1280) | | | 28440 (196) (2000) | 22470 (155) (1580) | 17710 (122) (1245) |
| Clamping force | USton (kN) (tf) | 237 (2110) (215) | ||||||
| Clamping stroke | inch (mm) | 29.9 (760) | ||||||
| Min. mold thickness | inch (mm) | 11.4 (290) | ||||||
| Max. daylight opening | inch (mm) | 41.3 (1050) | ||||||
| Tie bar clearance (H×V) | inch (mm) | 24.0×24.0 (610×610) | ||||||
| Die plate dimensions (H×V) | inch (mm) | 34.3×34.3 (870×870) | ||||||
| Ejector stroke | inch (mm) | 4.7 (120) | ||||||
| Item | Unit | 71A (std) | | | 100A | ||||
|---|---|---|---|---|---|---|---|---|
| Screw diameter | inch (mm) | A 2.20 (56) | B 2.48 (63) | C 2.80 (71) | | | A 2.48 (63) | B 2.80 (71) | C 3.15 (80) |
| Injection capacity | inch3 (cm3) (oz) | 33.8 (554) (18.6) | 42.8 (701) (23.5) | 54.4 (891) (29.9) | | | 48.5 (795) (26.6) | 61.6 (1010) (33.8) | 78.1 (1280) (42.9) |
| Max. injection pressure | psi (MPa) (kgf/cm2) | 28440 (196) (2000) | 22470 (155) (1580) | 17710 (122) (1245) | | | 29790 (205) (2095) | 23390 (161) (1645) | 18490 (127) (1300) |
| Clamping force | USton (kN) (tf) | 309 (2740) (280) | ||||||
| Clamping stroke | inch (mm) | 32.7 (830) | ||||||
| Min. mold thickness | inch (mm) | 12.6 (320) | ||||||
| Max. daylight opening | inch (mm) | 45.3 (1150) | ||||||
| Tie bar clearance (H×V) | inch (mm) | 26.0×26.0 (660×660) | ||||||
| Die plate dimensions (H×V) | inch (mm) | 37.6×37.6 (955×955) | ||||||
| Ejector stroke | inch (mm) | 5.1 (130) | ||||||
| Item | Unit | 100A (std) | | | 140A | ||||
|---|---|---|---|---|---|---|---|---|
| Screw diameter | inch (mm) | A 2.48 (63) | B 2.80 (71) | C 3.15 (80) | | | A 2.80 (71) | B 3.15 (80) | C 3.54 (90) |
| Injection capacity | inch3 (cm3) (oz) | 48.5 (795) (26.6) | 61.6 (1010) (33.8) | 78.1 (1280) (42.9) | | | 67.7 (1100) (37.2) | 86.0 (1410) (47.2) | 108.6 (1780) (59.6) |
| Max. injection pressure | psi (MPa) (kgf/cm2) | 29790 (205) (2095) | 23390 (161) (1645) | 18490 (127) (1300) | | | 28390 (195) (1990) | 22330 (154) (1570) | 17710 (122) (1245) |
| Clamping force | USton (kN) (tf) | 398 (3540) (361) | ||||||
| Clamping stroke | inch (mm) | 38.2 (970) | ||||||
| Min. mold thickness | inch (mm) | 13.8 (350) | ||||||
| Max. daylight opening | inch (mm) | 52.0 (1320) | ||||||
| Tie bar clearance (H×V) | inch (mm) | 28.9×28.9 (735×735) | ||||||
| Die plate dimensions (H×V) | inch (mm) | 41.5×41.5 (1055×1055) | ||||||
| Ejector stroke | inch (mm) | 5.9 (150) | ||||||
| Item | Unit | 160A (std) | ||
|---|---|---|---|---|
| Screw diameter | inch (mm) | A 2.80 (71) | B 3.15 (80) | C 3.54 (90) |
| Injection capacity | inch3 (cm3) (oz) | 77.5 (1270) (42.6) | 98.2 (1610) (54.0) | 123.9 (2030) (68.0) |
| Max. injection pressure | psi (MPa) (kgf/cm2) | 28390 (195) (1990) | 22330 (154) (1570) | 17710 (122) (1245) |
| Clamping force | USton (kN) (tf) | 501 (4460) (455) | ||
| Clamping stroke | inch (mm) | 40.4 (1025) | ||
| Min. mold thickness | inch (mm) | 14.8 (375) | ||
| Max. daylight opening | inch (mm) | 55.1 (1400) | ||
| Tie bar clearance (H×V) | inch (mm) | 32.3×32.3 (820×820) | ||
| Die plate dimensions (H×V) | inch (mm) | 46.9×46.9 (1190×1190) | ||
| Ejector stroke | inch (mm) | 6.3 (160) | ||
A: The series offers clamping forces ranging from 81 to 455 tons, accommodating various molding needs.
A:The X-Pump® system operates the servomotor only when necessary, leading to significant energy savings compared to traditional hydraulic systems.
A: The Nissei TACT5 controller acts as a smart, centralized network hub for your molding floor. It makes your injection molding machine act as the central brain for connected equipment, simplifying complex operations and reducing downtime. This includes directly connecting with and controlling auxiliary equipment, the ability to perfectly sync and automate a production cell, monitor it remotely, and make changes on the fly. Also, OPC-UA communication connects production scheduling software (like MES or ERPs). For specifics, please contact one of our team members.
A: Yes, the FNX-IV Series is designed for a wide variety of molding applications, from precision thin-wall to thick-wall products.
A: The hybrid design combines hydraulic cost efficiency with electric servomotor precision, upgraded with advanced maintenance features for the FNX-IV series. The TACT5 enables instant off-site troubleshooting. In addition, future updates will enable predictive maintenance to further prevent downtime.
